Results 1 to 10 of 10
Thread: car stalling
-
04-05-2010, 06:12 AM #1
car stalling
Ive got my girlfriends 96 bonneville vin k no supercharger and its got a rough idle when it wants to, it stalls and throws a P0336-crankshaft position (ckp) sensor A performance code so I put a crank position sensor in it (bought it from the dealer so it ac delco part) and its doing it again so im woundering if anybody has some ideas
-chris
-
04-05-2010, 06:20 AM #2
- Join Date
- Nov 1999
- Location
- over here...
- Age
- 45
- Posts
- 25,709
[]D [] []V[] []D- 1999 trans am
how long ago was the fuel filter and air filter replaced???
-
04-05-2010, 08:29 AM #3
How long ago did you replace the sensor? Might wanna chase the wiring to ensure its not grounding out befor it reaches the Icm.. Also make sure the connector is clean and tight.
J2001 SS, Its not the car its the Driver that matters....
-
04-06-2010, 12:09 PM #4
-
04-06-2010, 12:12 PM #5
-
04-22-2010, 04:59 PM #6
Im still having problems with this car throwing same codes so today i got a crank sensor pigtail and wired it up to the ignition module and stared it up and still studders when revving it up and stalls out but now throwing a diffrent code P0341 camshaft position sensor performance code where do I go from here im lost
-
04-22-2010, 08:15 PM #7
If you are getting a code for a camshaft sensor now then is very possible that is bad too. Did you clear all the codes after you replace the crankshaft sensor? My nissan altima had the code for the crankshaft sensor. I replaced it and the car won't start. I cleared the codes and try again. It didn't start but I had the camshaft sensor code. Replaced the camshaft sensor and it started right away. Hope that helps. Good luck
-
04-23-2010, 09:47 PM #8
Yeah I have hptuners so I can clear codes with that it comes on everytime I drive it. Im woundering since I did the wiring for the crank sensor and that code went away that maybe since I moved the cam sensor wiring when I did the crank sensor that I disturbed it and should rewire it to so idk
-
04-24-2010, 05:00 PM #9
How many miles on your old lady's car? It is possible that the timing chain is worn and has a lot of slack in it.
-
04-25-2010, 01:04 PM #10
about 105k i dont think its in the chain they last longer than that its got to be electrical its just weird it went from crank sensor to cam sensor but I gusse we had a bonneville at work do the same thing and the tech ran a new 5 volt refrence wire to the cam sensor and fixed it so I may do the same
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
my car is stalling
By jAgZ28 in forum LT1Replies: 6Last Post: 03-12-2011, 06:55 PM -
Car Stalling??????????
By ptownboy420 in forum General HelpReplies: 12Last Post: 07-17-2010, 08:06 AM -
Stalling
By lsx camaro in forum Internal EngineReplies: 11Last Post: 07-10-2009, 01:19 PM -
Car stalling
By paulc87 in forum General HelpReplies: 3Last Post: 01-24-2008, 06:48 AM -
Z stalling out
By 94redmaro in forum General HelpReplies: 2Last Post: 05-30-2007, 02:58 PM
Bookmarks