Results 1 to 10 of 10

A-Pillar

This is a discussion on A-Pillar within the Appearance Section forums, part of the General Help category; ive been searching for an A-Pillar that will hold 3 gauges....but the only A-Pillars that i can seem to find ...

  1. #1
    Senior Member Z28boy2000's Avatar
    Join Date
    Jun 2008
    Location
    Rochester, NY Rochesterracing.com
    Posts
    1,276
    2000 Camaro B4C

    A-Pillar

    ive been searching for an A-Pillar that will hold 3 gauges....but the only A-Pillars that i can seem to find are for T-Top T/A's and Z's. Does anyone know where i can get the triple pillar pod for a hard top
    2000 B4C Special Service Package Z28 - Kooks 1&7/8 Stepped 2'' - TSP Torquer V.2 - FAST 92/92 - BDR 4000 Conveter - Xtreme Trans Stage II - Full UMI Suspension - Pacesetter LT's - Comp Drag Shocks - Magnaflow - Cutout - ZO6 MAF - FTP LID - Street Tuned -

  2. #2
    Sold: LS1 '85 El Camino ls1camino's Avatar
    Join Date
    Dec 2005
    Location
    Laurel, Maryland
    Posts
    4,977

    2000 Grand Prix GTP
    2000 Trans Am WS6 M6

    I don't think they make one. All you have to do is buy a t-top one and cut the lip off of the top to fit the hardtop.

  3. #3
    Senior Member Z28boy2000's Avatar
    Join Date
    Jun 2008
    Location
    Rochester, NY Rochesterracing.com
    Posts
    1,276
    2000 Camaro B4C

    Yeah that's what I was thinking

    How hard is it to instal the gauges into the car...wiring ect.

  4. #4
    Sold: LS1 '85 El Camino ls1camino's Avatar
    Join Date
    Dec 2005
    Location
    Laurel, Maryland
    Posts
    4,977

    2000 Grand Prix GTP
    2000 Trans Am WS6 M6

    Quote Originally Posted by Z28boy2000 View Post
    Yeah that's what I was thinking

    How hard is it to instal the gauges into the car...wiring ect.
    It's wasn't bad (did mine last summer). Since I'm a perfectionist, I spent a lot of time making the wiring neat, eventhough it is hidden...total time was about a day. I then took it all apart over the winter to install digital gauges.

    I have a Wideband A/F, Fuel Pressure, and Tach/Shiftlight.

  5. #5
    Senior Member Z28boy2000's Avatar
    Join Date
    Jun 2008
    Location
    Rochester, NY Rochesterracing.com
    Posts
    1,276
    2000 Camaro B4C

    how much did the whole set up cost you if you dont mind me asking (for the first setup)

  6. #6
    Junior Member 99LsOne's Avatar
    Join Date
    Jun 2009
    Location
    Spartanburg, South Carolina
    Posts
    24

    Pewter
    1999 Camaro z28

    yeah I'm goin with ls1camino on this one I was reading a Camaro Performance magazine last night and there was a 98 SS hradtop or maybe a 96 either way the picture he had a Triple Gauge Cluster on the pillar, he listed that he got it from autometer but when you look on there site they only sell triple gauge clusters for camaros 82-92 and ttops all the way through 02 so i'm guessing he trimmed it as well.

  7. #7
    Sold: LS1 '85 El Camino ls1camino's Avatar
    Join Date
    Dec 2005
    Location
    Laurel, Maryland
    Posts
    4,977

    2000 Grand Prix GTP
    2000 Trans Am WS6 M6

    Quote Originally Posted by Z28boy2000 View Post
    how much did the whole set up cost you if you dont mind me asking (for the first setup)
    $150 used from a member on here. Had the Carbon Fiber analog gauges...sold them for $150 to a friend (kept the pillar pod). I think I paid $2.500 or so for the digital gauges and sending units. I still need to buy a Wideband O2 Sensor

  8. #8
    Junior Member
    Join Date
    Jun 2007
    Location
    ct
    Posts
    61

    blue
    2002 ws6

    when i put mine up i took the cars pillar off lined up the new one over the old one and marked where the guages would go than cut large holes in the oem pillar, and glued the pod pillar to the oem pillar using 2 part epoxy cause i wanted a clean look instead of using screws or velcro ... when dried i put the gauges in ran the wires down the back of the oem side and repoped it on .. looks almost factory


    one note .. im assuming your looking for the complete sleeve .. when installing make sure that the cut out for the window vent is lined up if not widden the pods hole ..
    Last edited by ws6race; 06-15-2009 at 09:58 AM.

  9. #9
    Member Bouvers's Avatar
    Join Date
    May 2006
    Location
    Canada
    Age
    31
    Posts
    857

    Blue 1997 Trans Am(Sold)
    Pewter 2001 Trans Am Vert

    I've always wondered how bad the color difference is on these pod pillars I seem to see a few pics and they look mix matched colors any with them installed care to take a few photos...

  10. #10
    Sold: LS1 '85 El Camino ls1camino's Avatar
    Join Date
    Dec 2005
    Location
    Laurel, Maryland
    Posts
    4,977

    2000 Grand Prix GTP
    2000 Trans Am WS6 M6

    The come in a black that matches my 2000 Ebony interior perfectly...

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. B pillar
    By chevelle3504speed in forum Appearance Section
    Replies: 7
    Last Post: 12-16-2012, 03:25 PM
  2. Wanted: Pillar Pod
    By 1slowbusa in forum Parts Wanted / Trade
    Replies: 0
    Last Post: 07-31-2011, 03:30 PM
  3. Help: A pillar
    By 2000dreambird in forum Appearance Section
    Replies: 5
    Last Post: 08-02-2010, 09:00 PM
  4. tri pillar pod pics
    By 01ls1ws6 in forum Firebird / WS6
    Replies: 2
    Last Post: 04-28-2009, 12:27 PM
  5. Pillar Gauge Pod?
    By x10-wakerider in forum Appearance Section
    Replies: 4
    Last Post: 08-24-2005, 05:20 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •