Results 1 to 4 of 4

Center Console Fabrication HELP

This is a discussion on Center Console Fabrication HELP within the Appearance Section forums, part of the General Help category; I'm putting in a B&M Hammer Shifter tomorrow and I want to keep the stock center console top, only I ...

  1. #1
    VERITAS / AEQUITAS T/A Addicted's Avatar
    Join Date
    Jul 2009
    Location
    Ohio (Union county)
    Age
    41
    Posts
    92

    Pewter
    2002 T/A WS-6

    Question Center Console Fabrication HELP

    I'm putting in a B&M Hammer Shifter tomorrow and I want to keep the stock center console top, only I believe I'm going to be 1/4-1/2" shy in height. Seeing how the top is seperate from the rest of the console, I'm tring to think up a fix. (SUGGESTIONS) I'm considering some type of ring that will rest on the console bottom raising it up the required amount and then re-installing the top onto that. It would need to be solid and some type of bracket/brace to raise the rear bolts (which would need to be longer) that hold it into place.

    Does anyone know of sombody on here with the right raw materials and equipment to knock this out and make it look good.
    Last edited by T/A Addicted; 09-03-2009 at 11:25 AM. Reason: no hits

  2. #2
    lmpounded SandmanWs7's Avatar
    Join Date
    Jan 2006
    Location
    Dallas, Texas
    Posts
    8,028

    Silver
    2007 CTS-V

    So you want a huge 1/4" to 1/2" spacer to put on the bottom of the whole center console?

  3. #3
    lmpounded SandmanWs7's Avatar
    Join Date
    Jan 2006
    Location
    Dallas, Texas
    Posts
    8,028

    Silver
    2007 CTS-V

    This was yesterdays post. Did you install the shifter? Pics of how it's higher than the console?

  4. #4
    VERITAS / AEQUITAS T/A Addicted's Avatar
    Join Date
    Jul 2009
    Location
    Ohio (Union county)
    Age
    41
    Posts
    92

    Pewter
    2002 T/A WS-6

    Its a mout point shifter won't go in w/o custom linkage JEGS misquoted took it back today thx anyway
    SFC's/85mmMAF/Cold Air Induc./Smooth Bellows/Spohncross member mntdAdj.TQArm STB /F&R EdelbrockPrfmrAISShocks F&RPolyswaybarkit&PolyMotor&Tran Mnts/TransGoHPShftKit/QTP SS LTHdrs no cats/Borla Cat Back/QTPCutout /AEM Wideband UEGO Controller /IPS tune

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Hot center console
    By phoenix05 in forum General Help
    Replies: 45
    Last Post: 04-29-2011, 02:11 PM
  2. 97-02 Center Console
    By 96Firebirdformula in forum Firebird / WS6
    Replies: 3
    Last Post: 08-05-2008, 06:52 PM
  3. 93-97 T/A center console......
    By qwk93ta in forum Parts For Sale / Trade
    Replies: 17
    Last Post: 07-16-2008, 03:51 AM
  4. Anybody need a Center Console?
    By TooFastT/A in forum Rocky Mountain Members
    Replies: 0
    Last Post: 07-26-2007, 11:29 PM
  5. Anyone have a center console / center vent for a T/A?
    By WICKED LS1 in forum Parts Wanted / Trade
    Replies: 1
    Last Post: 07-24-2007, 01:27 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •