Turn Signal confused

**FutureWS6** · 10-31-2009, 03:35 PM

Ok, its not really confused, but.. When i try the left side the left side lights up. but no flashing, same for right side. Hazards still work fine so no bulbs out. No clue to what it would be.

**Adam_94_T/A** · 10-31-2009, 03:43 PM

Originally Posted by FutureWS6

Ok, its not really confused, but.. When i try the left side the left side lights up. but no flashing, same for right side. Hazards still work fine so no bulbs out. No clue to what it would be.

check your grounds just did it to mine had the same problem. Use a jumper to jump the ground to the bub socket.

**FutureWS6** · 10-31-2009, 04:14 PM

Originally Posted by Adam_94_T/A

check your grounds just did it to mine had the same problem. Use a jumper to jump the ground to the bub socket.

under the steering colom?

**Adam_94_T/A** · 10-31-2009, 04:21 PM

no pull the tail lights and check the ground wires running to the bulb and socket sometimes the ground wires come loose and it has a tacky ground. so it makes the lights stay solid while the turn signals are on either side.

**SiggyZ** · 11-02-2009, 08:48 AM

I have an issue with my signals blinking slower when the A/C is running. I just assume it's a power pull somewhere.

**Adam_94_T/A** · 11-02-2009, 12:07 PM

Originally Posted by SiggyZ

I have an issue with my signals blinking slower when the A/C is running. I just assume it's a power pull somewhere.

hmmmm never really had that kinda problem but sounds to be just that. if they work then they are fine lol

**SiggyZ** · 11-02-2009, 12:13 PM

I agree. Now, if they were doing this all the time, I'd probably put my money on the flashers going out. I had that happen once on a previous Camaro.

Originally Posted by Adam_94_T/A

hmmmm never really had that kinda problem but sounds to be just that. if they work then they are fine lol

**shady milkman** · 11-02-2009, 12:14 PM

check your relay..look in your manual and find out where it is at exactly.

**shady milkman** · 11-02-2009, 12:15 PM

Originally Posted by FutureWS6

Ok, its not really confused, but.. When i try the left side the left side lights up. but no flashing, same for right side. Hazards still work fine so no bulbs out. No clue to what it would be.

also..your bulbs are dual filament ..

**Adam_94_T/A** · 11-02-2009, 01:05 PM

Originally Posted by shady milkman

also..your bulbs are dual filament ..

This is also true. The thing i noticed is when mine weren't ground out correctly the second filament wouldn't light. When i hooked my jumper to the wire and bulb socket it light and worked. Which led me to the conclusion that this was his problem. Also the signs were similar to what mine was doing. As for the relay that could be a possible source of the signals flashing slow then normal (Constant) or it could even be the flasher under the dash.

**bigrondownhiller** · 11-02-2009, 02:08 PM

First try the flasher. You could switch it with the hazard one and see if that fixes the problem. If not you have to start checking bulbs and sockets.

**Adam_94_T/A** · 11-02-2009, 02:14 PM

Originally Posted by bigrondownhiller

First try the flasher. You could switch it with the hazard one and see if that fixes the problem. If not you have to start checking bulbs and sockets.

There is only one flasher and it is located under the dash on drivers side which means there is no switching of a flasher. As for the relays a relay is either good or bad.