Results 1 to 16 of 16
Thread: New FRCs and Lid
-
03-04-2009, 07:09 PM #1
New FRCs and Lid
Update: Lid installed. Pic below.
Last edited by onetroubledguy; 03-09-2009 at 05:43 PM.
-
03-04-2009, 07:29 PM #2
have you ever changed your own air filter? If you have then you can change your lid
-
03-04-2009, 07:30 PM #3
Actually I haven't lol, but shouldn't be too hard. Thanks.
-
03-04-2009, 08:46 PM #4
- Join Date
- Mar 2008
- Location
- Colorado
- Posts
- 191
Mystic Teal/Chameleon grn- 1998 TA
wow that looks really good. The hardest part about putting the lid on is getting the MAF in there. Other than that its easy. Where did you get the FRC's?
-
03-04-2009, 09:40 PM #5
ya installing is real simple.. but i would also like to no where go got those FRC's they look legit
-
03-05-2009, 05:14 AM #6
PontiacFan on the board here did mine. Jaison from Third Shift Studios does them as well.
-
03-05-2009, 05:17 AM #7
- Join Date
- Oct 2008
- Location
- Miami, Fla
- Posts
- 200
Spiral Gray- 2004 Auto Corvette
Sweet looking parts!!!
-
03-05-2009, 07:34 AM #8
-
03-05-2009, 11:41 AM #9
- Join Date
- Jun 2007
- Location
- Dalzell, Illinois
- Age
- 35
- Posts
- 899
red with black stripes- 2002 Trans Am WS6
the install isnt bad on the covers after you have done them a couple times you get the hang of it. take the tape off the fuel lines, move the two main connectors for the coil harnesses down and they should go right on.
-
03-05-2009, 12:10 PM #10
If the lid don't fit easily over the maf take a hair dryer to it and warm up the hole a bit that will make it slide right on. Mine took 15 minutes just because I sat there like a monkey screaming what I was doing wrong.
-
03-05-2009, 12:28 PM #11
-
03-05-2009, 04:36 PM #12
The instructions from SLP are really detailed, but not in a good way. I really didn't think it was as complicated as they make it out to be.
-
03-05-2009, 06:50 PM #13
-
03-09-2009, 05:28 PM #14
Posted a pic of the lid installed (it's an SLP btw). It was an easy install, but it didn't fit well. I got it as tight as I could but it still seems a little loose for my liking.
If the lid don't fit easily over the maf take a hair dryer to it and warm up the hole a bit that will make it slide right on. Mine took 15 minutes just because I sat there like a monkey screaming what I was doing wrong.Last edited by onetroubledguy; 03-09-2009 at 05:49 PM.
-
03-10-2009, 08:40 AM #15
- Join Date
- Nov 2007
- Location
- Philly, PA
- Age
- 40
- Posts
- 2,055
Black- 2001 Firebird TransAm WS6
looks good
-
03-11-2009, 03:01 PM #16
the new slp lids dong come with any thing for a gasket so it would be a good idea to go to a hard where store and get 1/2 windo fome and make it so it dont leak
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Selling LS6 Intake Manifold and Corvette FRCs
By WS6Dream in forum Parts For Sale / TradeReplies: 15Last Post: 05-18-2011, 04:39 PM -
Misc(FRCs,AdjTqArm,StrutBar,StealthBox,BillitGrill e,+M ore!)
By Selride in forum Parts For Sale / TradeReplies: 12Last Post: 11-28-2010, 10:12 AM -
Installed FRCs, if you need help let me know!
By onetroubledguy in forum Appearance SectionReplies: 13Last Post: 03-25-2009, 07:21 PM -
LS6 Manifold, PCV System, Shifter, FRCs, etc.
By ls1camino in forum Parts Wanted / TradeReplies: 10Last Post: 11-08-2008, 06:58 PM -
Corvette FRCs
By KAOTIK in forum Parts For Sale / TradeReplies: 3Last Post: 12-20-2005, 04:08 PM
Bookmarks