Exhaust Tips

**dschribs** · 01-22-2015, 04:22 AM

Anyone purchase exhaust tips from this site??

Stainless Steel Clone Exhaust Tips

Just wondering how the quality is...

**theorangeguy** · 01-22-2015, 05:40 AM

they are very good quality. I know quite a few people who have ordered from there and have been very happy with the purchase.

**2002ssslp** · 01-22-2015, 06:02 AM

Outstanding quality for the price. Those tips will outlast you exhaust system.

**dschribs** · 01-22-2015, 07:56 AM

Exactly what I was hoping to hear!

Thanks!

**dschribs** · 01-22-2015, 08:18 AM

Quick follow up...

The longer of the two tips on either pair goes in towards the license plate correct?

**Nutball** · 01-22-2015, 08:19 AM

Originally Posted by dschribs

Quick follow up...

The longer of the two tips on either pair goes in towards the license plate correct?

Yes

***SMWS6TA*** · 01-22-2015, 08:26 AM

Originally Posted by dschribs

Quick follow up...

The longer of the two tips on either pair goes in towards the license plate correct?

Originally Posted by Nutball

Yes

<<Oops...

**pajeff02** · 01-23-2015, 02:59 AM

Good looking tips and the price is nice.

**nathan c** · 02-23-2015, 07:38 AM

What size did you order?

**dschribs** · 02-24-2015, 06:55 AM

I ordered the 3.5". Haven't installed them yet but they look like the perfect size.

**Badass WS6** · 02-27-2015, 02:32 PM

I had those tips on both my previous '99 Z and '02 WS6.

No complaints here on either vehicle.

**ASh302** · 02-27-2015, 05:57 PM

Those are the best I have every used, I had them on my 2013 GT, did the 2013 Shelby GT500 lower valance and used those tips and was just in love with them.

ASh

**ASh302** · 03-06-2015, 07:16 AM

Well I came across some of these used on Ebay and grab them, they came off of I believe a 01 WS6, got them for $50 shipped
I'm happy camper. They should fit the rear bumper cutout area nice. Again I loved these on my 13 GT, they just look so good
Can't wait to have them on the T/A

ASh

**Whamhammer** · 03-06-2015, 08:05 AM

Originally Posted by ASh302

Well I came across some of these used on Ebay and grab them, they came off of I believe a 01 WS6, got them for $50 shipped
I'm happy camper. They should fit the rear bumper cutout area nice. Again I loved these on my 13 GT, they just look so good
Can't wait to have them on the T/A

ASh

I was under the impression that 99+ WS6 exhaust tips were essentially part of the tailpipe?

**ASh302** · 03-06-2015, 08:11 AM

Originally Posted by Whamhammer

I was under the impression that 99+ WS6 exhaust tips were essentially part of the tailpipe?

idk, I mean you can or cannot run the exhaust tip? depends on what you want. to be honest I'm trying to understand what you are saying about "essentially part"
right now I'm running SLP single exhaust tips, but once I found these, I'll be swapping to the new tips.

ASh

**sjgreen6** · 03-06-2015, 03:51 PM

Originally Posted by ASh302

idk, I mean you can or cannot run the exhaust tip? depends on what you want. to be honest I'm trying to understand what you are saying about "essentially part"
right now I'm running SLP single exhaust tips, but once I found these, I'll be swapping to the new tips.

ASh

If you have an aftermarket exhaust you can probably unbolt the clamp and remove the current tip if it hasn't been welded on then swap on whatever suits you as long as it fits and is properly centered. If you have the factory exhaust, the stainless tips are welded on to the pipes so you would need to cut them off then possibly fabricate an extension to get the tips to sit in the right location. Good luck!

**ASh302** · 03-06-2015, 07:28 PM

I'll see when they get here, they were already on a T/A and saw the pictures, they did cut them with a little pipe, but I'm going to see if I can cut it down and be able to side em on some how, if not will need to get them welded, which is fine, but cost a little cash.

ASh