Results 1 to 20 of 34
-
03-19-2008, 05:27 AM #1
- Join Date
- Jul 2005
- Location
- Central TX
- Age
- 43
- Posts
- 1,694
Sunset Orange Metallic- 2002 WS6
cracks in your taillights? Door Panel?
Is it normal for your tail lights to get small cracks? I just noticed mine has one on passenger side.
Also, I noticed my interior has the same crack on the door panel on each side...
anyone in the same boat? Anything you can really do about it?
-
03-19-2008, 06:12 AM #2
- Join Date
- Aug 2005
- Location
- Pittsburgh, PA
- Age
- 42
- Posts
- 21,720
My life is a- Ben Stiller movie.
audrey, do a search about the door crack-it's common and very unforgiving-but someone posted a fix. It might be in the appearance stickys.
Dunno about your taillight. Is it just the lens cover or the housing?
-
03-19-2008, 06:16 AM #3
-
03-19-2008, 06:20 AM #4
- Join Date
- Jul 2005
- Location
- Central TX
- Age
- 43
- Posts
- 1,694
Sunset Orange Metallic- 2002 WS6
Yup, found it (cracked door panels)
http://www.highperformancepontiac.co...air/index.html
his does not cover aesthetics. This fix is all about preventing future cracking. My crack was not very large and all I have to do (after the following fix) is carefully trim the stressed plastic out of the crack and shoot a shot of color matched vinyl paint over it. Further, to fix the crack itself, all I had to do was push the plastic together, throw on some JB Weld with some reinforcing plastic over that.
Hardware: For each Panel- Ten #4-40 screws/bolts and ten #4 washers. The shortest I could find were ½”, I cut them down to about 5/16. You just need to verify each screw (with washer) will go through with just enough thread to mate with the nut when finger tight.
After the panel is off, and before you take any of the staples out, drill your holes for the screws just above each staple except for the staple closest to the speaker - we are going to leave that one in.
Take out the staples, all but the one closest to the speaker.
A rotary toll will make this much easier, but I imagine you could just cut the holes with an exacto or even a small round file. The idea of this step is to not make the hole bigger, but to make each hole an oval - this is what will provide relief for future expansion/contraction.
Now clean up any rough plastic edges left from drilling the holes. I used a small chisel to clean both sides and an exacto to clean up the inside.
Starting from the end with the staple, begin putting your screws in with one washer on each screw. Put the screw in from the back If you don’t you will have fitment problems getting the panel back on.
Make sure you LocTite each nut, and only tighten hand tight.
All done. Like I said, I’m just going to carefully clean up the stressed plastic and spray some color matched vinyl spray over it and it will be as good as new and I am confident it will not crack again.
I don't want people to miss the point of this mod: That the oval holes and washer/screw allow the panel to expand and contract unlike the staples or just replacing the staples with rivets.
-
03-19-2008, 09:12 AM #5
Check these out! Someone needs to start a petition for recall and contact GM
http://rides.webshots.com/album/562650026XVVrXC
I must have one of the few virgin '99 door panels with no cracks. Door panels have never been off the car and they are still perfect! Imagine that.1999 BLACK WS6 RAM AIR TRANS AM A4 (1 of 274 WS6 coupe Canada only models)
ASC conversion date: 6/10/99
ASC build# : 4310 of 5007
Hood Sequence #74992V
w/over (50) performance & appearance mods!!!
My Albums: http://community.webshots.com/user/kenawink
-
03-19-2008, 09:43 AM #6
- Join Date
- Jul 2005
- Location
- Central TX
- Age
- 43
- Posts
- 1,694
Sunset Orange Metallic- 2002 WS6
mine were virgins until 2 weeks ago when I discovered 2 mysteries cracks!!!
-
03-19-2008, 09:49 AM #7
-
03-19-2008, 11:36 AM #8
-
03-19-2008, 06:23 PM #9
our door panels crack?
-
03-19-2008, 06:54 PM #10
-
03-19-2008, 07:16 PM #11
I reiterate :
http://rides.webshots.com/album/562650026XVVrXC
-
03-20-2008, 05:50 PM #12
- Join Date
- May 2006
- Location
- Canada
- Age
- 38
- Posts
- 854
Blue 1997 Trans Am(Sold)- Pewter 2001 Trans Am Vert
why don't we make a sticky on this issue?... everyone with the crack post it... maybe gm can see the issue.
Nevermind "lets give GM a reason to make a new TA" lets give them a reason to perfect the last ones... jesus I'm so burned to the fact that I have to replace a panel that they screwed up on and that the stealerships up here are asking 900$ a pop for them!
-
03-20-2008, 06:23 PM #13
- Join Date
- Jul 2005
- Location
- Central TX
- Age
- 43
- Posts
- 1,694
Sunset Orange Metallic- 2002 WS6
why doesn't GM do a recall since all do this?
-
03-20-2008, 07:01 PM #14
-
03-21-2008, 05:12 AM #15
Just finished replacing both window motors yesterday. Fixed a headlight motor last summer. Both door panels are still cracked as well as as the passenger side tail light lens. 2003 lenses are supposed to fit, I'll wait till I find some.
-
03-21-2008, 07:39 AM #16
- Join Date
- Jul 2007
- Location
- Lakewood, California
- Posts
- 779
Red/Silver/Black/Red- TA-G8-Expe-L200-Camaro
Lens Housing
Hey Buddy! Where are you at in California. I'm here in Lakewood!
I replaced the driver side motor a couple months ago. Both of my doors are cracked and I should have fixed that crack when I had the driver side off. Didn't think of it though.
What I hate the most is front signal housing for they crack because of the Running light heat......... no matter how I seal the housing, it will always have an area where it leaks in. I guess the heat just deteoriates the cement where I caulk the crack.
Sucks,
Matt
P.S. Your best bet on this issue is to solder the wires to kill the running lights.
-
08-17-2009, 11:40 PM #17
- Join Date
- May 2009
- Location
- Prattville, Al.
- Posts
- 4
Monterey Maroon- 2000 Trans Am
-
08-18-2009, 08:40 AM #18
- Join Date
- Jun 2009
- Location
- Saint Louis, MO
- Posts
- 1,705
Arctic White & Black- '98 WS6 M6 - SWAPTIME!
I just noticed my passenger tail light was cracked and couldn't find a reasonable replacement for just a cosmetic crack so I went with black outs instead... Fixed the problem of my eyesore
-
08-18-2009, 10:40 AM #19
- Join Date
- Nov 2007
- Location
- RICHMOND VA
- Posts
- 213
RED- 2002 FORMULA
Good luck finding the 2003 lenses for you bird.
-
08-18-2009, 11:03 AM #20
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
WTB: Trans Am Driver's door panel (Ebony) w/ NO CRACKS!
By eb2phkingood in forum Parts Wanted / TradeReplies: 3Last Post: 07-10-2012, 12:25 PM -
WTB: Trans Am Driver's door panel (Ebony) w/ NO CRACKS!
By eb2phkingood in forum Parts Wanted / TradeReplies: 0Last Post: 07-10-2012, 09:47 AM -
Firebird Door Panel Crack Repair - Door Panel Pandemic
By Ed Blown Vert in forum Firebird / WS6Replies: 0Last Post: 10-18-2007, 10:50 AM -
Door Panel Cracks
By wnmech in forum Firebird / WS6Replies: 17Last Post: 02-22-2007, 12:05 AM -
Door panel cracks
By sundevil54 in forum Firebird / WS6Replies: 32Last Post: 10-08-2006, 11:47 AM
Bookmarks