Results 1 to 7 of 7

Window/door problems

This is a discussion on Window/door problems within the Camaro / SS forums, part of the Vehicle Specific category; I have noticed that if I roll the drivers window all the way down it seems to push the door ...

  1. #1
    Junior Member
    Join Date
    Mar 2007
    Location
    Harmony NC
    Age
    41
    Posts
    22

    Pewter
    2000 Z28

    Window/door problems

    I have noticed that if I roll the drivers window all the way down it seems to push the door panel out some. Then when I roll it back up it "pop" before it starts rolling up. Any idea what might be broken or out of alignment?

  2. #2
    Junior Member
    Join Date
    Mar 2007
    Location
    manassas, VA
    Posts
    7

    Silver
    99 z28 camaro

    i would pull off the door panel and take a look thats the only way youll find out for sure

  3. #3
    UberTapping Friction Pimp Anthracis's Avatar
    Join Date
    Mar 2007
    Location
    Omar's Tittie Taverna & Grill, Deh Rawod
    Posts
    1,447

    18D Cock Diesel
    1999 Z28; 98 SS #2043 RIP

    one of the window regulator bolts may be loose and when your window is down the motor is moving and thus pushes in towards the door panel causing it to move. But this is all conjecture until you remove the door panel and have a look.

  4. #4
    Junior Member
    Join Date
    Feb 2007
    Location
    San Jose, CA
    Posts
    27

    Red
    2002 Camaro SS

    Quote Originally Posted by Anthracis View Post
    one of the window regulator bolts may be loose and when your window is down the motor is moving and thus pushes in towards the door panel causing it to move. But this is all conjecture until you remove the door panel and have a look.
    I agree.... i had a similar problem and adjusted the regulator bolts and now the window goes up and down without any problems.

  5. #5
    Member Corey1987's Avatar
    Join Date
    Oct 2006
    Location
    Greenville, NC
    Age
    30
    Posts
    231

    Black
    1998 Z/28

    mine does the EXACT same thing, i have noticed today that if i roll mine almost all the way down, the window can move forward and back about an inch and a half, guess i just gotta take off my door panel and check.

  6. #6
    UberTapping Friction Pimp Anthracis's Avatar
    Join Date
    Mar 2007
    Location
    Omar's Tittie Taverna & Grill, Deh Rawod
    Posts
    1,447

    18D Cock Diesel
    1999 Z28; 98 SS #2043 RIP

    be careful when removing the door panel. Those clips can be quite fragile.

  7. #7
    Chevy Power LS1RacerMan30's Avatar
    Join Date
    Aug 2006
    Location
    Canyon Country,California
    Age
    41
    Posts
    40

    Silver
    1995 Chevy Camaro LT1

    Yea,Mine did that same shit.I took the door panel off and it came off track and one of the bolts to the regulator came loose and fell off.So I put the bolt back in and put the window back in the crease in the window seal to line it back up and the window worked fine after that.Make sure when U re align the window use the motor to line up the bolts while holding the window straight

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Help: Power window hitting door?
    By CD99Firebird in forum General Help
    Replies: 20
    Last Post: 07-09-2015, 03:44 PM
  2. Door window guide
    By JWSmythe in forum General Help
    Replies: 0
    Last Post: 05-24-2008, 03:35 PM
  3. door Window outside weatherstriping
    By slikws6 in forum General Help
    Replies: 1
    Last Post: 05-10-2008, 10:47 AM
  4. need driver door/w window
    By LS1buckey in forum Appearance Section
    Replies: 2
    Last Post: 03-18-2008, 05:56 PM
  5. Loose door window....Help!!!
    By jeremy_m70 in forum General Help
    Replies: 4
    Last Post: 08-05-2007, 02:47 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •