Results 1 to 8 of 8
Thread: O2 connector
-
05-30-2018, 08:03 AM #1
- Join Date
- May 2018
- Location
- lost send dogs & helicopter
- Posts
- 4
teal- 1999 Z 28
O2 connector
I need help figuring out how to access the bank 1 number 2 (rear) oxygen sensor connector on my wife's 1999 Z-28 LS1 I got the other 3 sensors off but the bank 1 rear sensor wiring plug is un-reachable as it is stuffed along the top of the tranny.
Any help would be treasured.
Thanks
dogman
-
05-30-2018, 08:25 AM #2
- Join Date
- Feb 2009
- Location
- Florida Man Status Acheivement
- Posts
- 11,759
Navy Blue Metallic- 98 T/A w/ mods, 00 FBVert
Get a floor jack and lower the transmission a little. It shouldn't be up there BTW, it should be along the side of the transmission.
http://www.ls1.com/forums/f7/my-6-liter-build-174257/
http://www.ls1.com/forums/f8/my-8-8-rear-build-165553/
6.0L Block - Forged 403ci , Polluter Stg3 Cam, FAST 102mm Intake, NW102 TB, MSD wires, NGK TR6 plugs, Truck Coil Packs, LS3 Fuel Injectors, CC Pacesetter LT Headers, TS&P ORY, QTP e-Cutout, Magnaflow Muffler, 104mm Air Lid & Line Lock, Catch Can, Stage 2 T56 w/Viper shaft, PRO 5.0 Shifter, Tick MC, SPEC Stg3+ Clutch, QT SFI BH, MWC DSL, Full UMI Performance Suspension, Belstein Shocks, Hotchkis Springs (1" Drop), YR1 Snowflake Wheels wrapped in NT555 tires & Custom Fab Ford 8.8 rear w/Wavetrac Diff 3.73 Yukon Gears, WSQ Hood, 3"CM Strange Eng Drive Shaft.
00 FB Vert - Stock
78 FB - Just getting started......
Horsepower never lies, but is often lied about!
-
05-30-2018, 08:38 AM #3
- Join Date
- May 2018
- Location
- lost send dogs & helicopter
- Posts
- 4
teal- 1999 Z 28
Actually it is along the top side but I can not reach it from underneath the car, is there an access panel under the consul shifter area on automatic tranny?
-
05-30-2018, 09:06 AM #4
- Join Date
- Feb 2009
- Location
- Florida Man Status Acheivement
- Posts
- 11,759
Navy Blue Metallic- 98 T/A w/ mods, 00 FBVert
no. If it was a manual you would have a larger hole that the shifter comes thru. Auto's only have an opening big enough for the shift cable to go thru.
-
05-30-2018, 02:22 PM #5
- Join Date
- May 2018
- Location
- lost send dogs & helicopter
- Posts
- 4
teal- 1999 Z 28
-
05-31-2018, 03:02 AM #6
I do not recall any issues accessing our O2 connectors. Is the connector attached to bracket on that side?
-
05-31-2018, 05:56 AM #7
- Join Date
- May 2018
- Location
- lost send dogs & helicopter
- Posts
- 4
teal- 1999 Z 28
Yes it was , I finally ended up getting my neighbor who has smaller hands to disconnect it and then connect the new one, his hands are just a little smaller than mine. The car is done and runs like a top , the only reason I did not eliminate these #2 sensors is I have to deal with strict emissions inspections every 2 years and do not want to leave my wife more problems to deal with when i'm gone.
Cheers,
Dogman
-
05-31-2018, 06:48 AM #8
- Join Date
- Feb 2009
- Location
- Florida Man Status Acheivement
- Posts
- 11,759
Navy Blue Metallic- 98 T/A w/ mods, 00 FBVert
What state?
If they're turned off they won't report. You could still leave them there. Think of it as spare O2's
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Help: Maf connector
By jking78 in forum General HelpReplies: 2Last Post: 08-11-2017, 04:11 PM -
What is this connector?
By silverWS6 in forum General HelpReplies: 6Last Post: 11-22-2009, 03:14 PM -
What is this connector for?
By Bassplayer92 in forum Stereo and ElectronicsReplies: 13Last Post: 05-12-2009, 12:31 PM -
Is this possible with a VGA connector?
By Mike Hawk in forum Almost Anything GoesReplies: 11Last Post: 02-04-2007, 03:26 AM -
WTB 5 pin maf connector???
By tooblue in forum Parts Wanted / TradeReplies: 0Last Post: 08-18-2005, 08:30 PM
Bookmarks