Results 1 to 4 of 4

Installed front end part...now I have codes

This is a discussion on Installed front end part...now I have codes within the Camaro / SS forums, part of the Vehicle Specific category; So I installed new struts, sway bar, and end links.Big job the car was full of rust. I got it ...

  1. #1
    Junior Member
    Join Date
    Apr 2014
    Location
    Tavares, FL
    Posts
    58

    Blue
    1998 Camaro Z28

    Installed front end part...now I have codes

    So I installed new struts, sway bar, and end links.Big job the car was full of rust. I got it all back together and took the car for a ride. The check Engine light was on. Car also didn't sound right and didn't shift right. After a awhile it started driving better. I pulled codes P0107, P1635, and a P0530. I know the P0530 is for the AC...Happens to be that my ac is leaking. Will get the checked tomorrow. Now the P0107 is for the mac which is hooked up properly. Had to bring the bolt for the struts that sits under the master cylinder which was moved out of the way. But nothing was hit when grinding. So not sure what the problem is. The only wire that was unhooked was the wire out the side of the master cyl, and I hooked that back up. Any ideas?

  2. #2
    Super Moderator
    pajeff02's Avatar
    Join Date
    Feb 2009
    Location
    Mansfield, PA
    Posts
    21,576

    Black & Blue
    '02 WS.6 / '07 Suburban

    Hmmm. I would start by checking your "ENG SENS" fuse to see if it is blown. Did you disconnect the battery during the install? If so, our cars almost always run poorly on first start up and will take a bit to settle in while the PCM relearns everything. Other than that, it sounds like something may have been disturbed during the install process - a connector that came loose, a ground wire that was detached or broken...

  3. #3
    Junior Member
    Join Date
    Apr 2014
    Location
    Tavares, FL
    Posts
    58

    Blue
    1998 Camaro Z28

    Got it all figured out. When I put the top strut bolts in I pinched off 2 wires to the ac switch there. No harm no foul.

  4. #4
    Super Moderator
    pajeff02's Avatar
    Join Date
    Feb 2009
    Location
    Mansfield, PA
    Posts
    21,576

    Black & Blue
    '02 WS.6 / '07 Suburban

    Good work on the fix. Problems like that can take a while to track down.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Help: Installed headers and throwing a few codes now
    By Sas in forum External Engine
    Replies: 28
    Last Post: 03-05-2012, 04:34 PM
  2. while were on the question of codes (part 2)
    By twozs in forum General Help
    Replies: 2
    Last Post: 04-15-2010, 07:07 PM
  3. codes throwing ses light part II
    By 00z28bubba in forum General Help
    Replies: 8
    Last Post: 11-03-2008, 05:30 PM
  4. New front suspension installed *pic
    By Soltakr in forum Suspension and Handling
    Replies: 5
    Last Post: 04-25-2007, 08:21 AM
  5. Anyone needs part or anything installed?
    By Frans96ss in forum Eastern Members
    Replies: 7
    Last Post: 05-16-2006, 09:53 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •