Results 1 to 5 of 5

Need a 10 bolt with 3.23 or 3.42

This is a discussion on Need a 10 bolt with 3.23 or 3.42 within the Parts Wanted / Trade forums, part of the Sponsors Group Pricing and Parts Review category; I want to trade my 10 bolt with 3.73 for a stock 10 bolt 2.73 or 3.23 or 3.42 i ...

  1. #1
    Junior Member
    Join Date
    Aug 2009
    Location
    VA
    Posts
    65
    iTrader
    0

    WHITE
    98

    Need a 10 bolt with 3.23 or 3.42

    I want to trade my 10 bolt with 3.73 for a stock 10 bolt 2.73 or 3.23 or 3.42 i dont like the gas mileage on the 3.73 gears am located in manassas,va

  2. #2
    Super Moderator
    pajeff02's Avatar
    Join Date
    Feb 2009
    Location
    Mansfield, PA
    Posts
    21,576
    iTrader
    1 (100%)

    Black & Blue
    '02 WS.6 / '07 Suburban

    I have my stock 10-bolt with 3.23's. Approximately 73,000 miles and NO noise or problems (other than the pinion seal weep that was apparently a factory option). The reluctors have been pressed off the axles and the backing plates, brakes, brake lines and wheel sensors are in use on my 12 bolt. I am about 2-1/2 hours north of Harrisburg.

  3. #3
    Junior Member
    Join Date
    May 2007
    Location
    Chas. WV 25303
    Posts
    66
    iTrader
    2 (100%)

    WHITE
    2002 Z28

    342 10 bolt rear end

    I have a 4-channel 342 10 bolt, yoke, backing plates FOR SALE $300.00 in Charleston, WV. Runs quietly in good condition. pics available.

  4. #4
    Junior Member
    Join Date
    Aug 2009
    Location
    VA
    Posts
    65
    iTrader
    0

    WHITE
    98

    My is a 3 channel rear....would a 4 channel work....can i see pics???

  5. #5
    Super Moderator
    pajeff02's Avatar
    Join Date
    Feb 2009
    Location
    Mansfield, PA
    Posts
    21,576
    iTrader
    1 (100%)

    Black & Blue
    '02 WS.6 / '07 Suburban

    You probably want a 3 channel then for everything to work properly. The 3 channel has the reluctor on the ring gear and ABS sensor on the center section. The 4 channel has them at the axle ends.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Bolt-In Rearend Buyers Guide - Bolt-In Rearends -
    By Ed Blown Vert in forum Almost Anything Goes
    Replies: 0
    Last Post: 08-25-2010, 03:40 AM
  2. Bolt-In Rearend Buyers Guide - Bolt-In Rearends -
    By Ed Blown Vert in forum Almost Anything Goes
    Replies: 0
    Last Post: 08-24-2010, 03:40 PM
  3. Bolt On Parts - Dyno Proven Bolt-ons - Tech
    By Ed Blown Vert in forum Camaro / SS
    Replies: 7
    Last Post: 10-01-2007, 05:37 PM
  4. Center bolt to Perimeter bolt Heads, Coil Mounting help
    By juiced99ws6 in forum Internal Engine
    Replies: 7
    Last Post: 03-31-2007, 12:38 AM
  5. wtb - 12 bolt - have cash & rebuilt 10 bolt for partial trade
    By wesTXwitesnake05 in forum Parts For Sale / Trade
    Replies: 0
    Last Post: 07-09-2006, 11:17 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •