Results 1 to 6 of 6

mti clear lid w/dual nozzles, where to mount them?

This is a discussion on mti clear lid w/dual nozzles, where to mount them? within the Nitrous forums, part of the LSx Technical Help Section category; i have a clear mti lid and i'm going to try and mount dual nozzles in the neck, aiming them ...

  1. #1
    Junior Member
    Join Date
    Apr 2006
    Location
    PA
    Age
    36
    Posts
    39

    Pewter
    2001 Z28

    mti clear lid w/dual nozzles, where to mount them?

    i have a clear mti lid and i'm going to try and mount dual nozzles in the neck, aiming them at the maf, BUT that damn IAT sensor is right there. should i mount the nozzle on that side(driver's side) infront of the iat, so i'm spraying past it, or in between the iat and the maf so that it's not spraying on the iat also?

  2. #2
    Senior Member mrr23's Avatar
    Join Date
    Jul 2005
    Location
    orlando, fl
    Posts
    7,134

    dark bowling green
    2000 corvette

    i did mine before the IAT.

  3. #3
    Junior Member
    Join Date
    Apr 2006
    Location
    PA
    Age
    36
    Posts
    39

    Pewter
    2001 Z28

    Quote Originally Posted by mrr23 View Post
    i did mine before the IAT.
    do you have any pics of your setup? i have the lid pulled and put the stocker on for now until i have the balls to try putting holes into my pretty lid. i was thinking about putting it about an inch behind the iat (towards the filter) and maybe notching the nozzle a little bit so that it sprays out more instead of right onto the sensor.

  4. #4
    Senior Member greatwhiteZ28's Avatar
    Join Date
    Nov 2006
    Location
    d
    Age
    33
    Posts
    3,675

    white
    2002 z28

    ive seen them on the left and right side of the outer edges, where it is flat ( on the sides)

  5. #5
    Senior Member mrr23's Avatar
    Join Date
    Jul 2005
    Location
    orlando, fl
    Posts
    7,134

    dark bowling green
    2000 corvette

    Quote Originally Posted by hallass View Post
    do you have any pics of your setup? i have the lid pulled and put the stocker on for now until i have the balls to try putting holes into my pretty lid. i was thinking about putting it about an inch behind the iat (towards the filter) and maybe notching the nozzle a little bit so that it sprays out more instead of right onto the sensor.
    mine was a single nozzle. just out the other one opposite of it.


  6. #6
    Junior Member
    Join Date
    Apr 2006
    Location
    PA
    Age
    36
    Posts
    39

    Pewter
    2001 Z28

    Quote Originally Posted by mrr23 View Post
    mine was a single nozzle. just out the other one opposite of it.

    Click for full size
    thanks for the pic. i went ahead and drilled the holes today and i'm pretty much in the same spot, but it's just a hair closer to the iat since it sits out a little bit farther on my lid. now if the rest of the lines and other nozzle will show up i'll be ready to go.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. How To Install Nitrous Nozzles
    By Ed Blown Vert in forum General Help
    Replies: 0
    Last Post: 12-05-2013, 06:50 PM
  2. two nozzles to spray evenly?
    By jmatt07 in forum Nitrous
    Replies: 1
    Last Post: 03-23-2009, 07:19 AM
  3. Replies: 1
    Last Post: 08-27-2007, 05:21 PM
  4. NX dual nozzles or the new MAF kit from NX??????
    By greatwhiteZ28 in forum Nitrous
    Replies: 4
    Last Post: 03-02-2007, 01:01 PM
  5. Replies: 0
    Last Post: 02-05-2007, 04:06 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •