Results 1 to 14 of 14
Thread: Estimated RWHP and Torque
-
05-03-2006, 10:01 AM #1
Estimated RWHP and Torque
Just got my Z06 with the mods listed. What kind of numbers do you guesstimate? Anyone know of a good dyno tune shop close to Dalton, Ga or Chattanooga, TN? I don't plan on doing anything else as far as performance mods, is there a hand held programmer that could give me some additional ponies? Thanks in advance!
Last edited by BLACKNIGHT03Z06; 05-03-2006 at 10:12 AM. Reason: Add signature with mods
02' Z06 EB/EB 4.6K miles, Longtubes, Off-road X, Pypes X-back, Blackwing CAI, Comp. Cam 238/240-.605/.609-112LSA, Comp. Beehive Springs, Comp. Titanium Retainers, Comp. Perf. Push Rods, Comp. Billet Double Roller Timing Chain, Hurst Short Throw, Cray 19"/20" w/ Toyo Proxes4 265/30/19's & 295/30/20's
-
05-03-2006, 02:32 PM #2
352.746 HP / 357.287 TQ @ 6200 RPMs
-
05-03-2006, 02:33 PM #3
just kidding, the only way to find out is dyno, some cars dyno alot higher than others stock for stock let alone with mods
i've heard nothing but bad about those handhelds, your best bet is a laptop program for personal use, or just a dyno tune where ever you get er dynoed.
-
05-09-2006, 05:06 PM #4
- Join Date
- Apr 2006
- Location
- michigan
- Age
- 54
- Posts
- 18
anniversary red- 2003 corvette
my stock 2003 ls1 dynoed at 306rwhp, it should be out of the performance shop tomorow. im looking for it to dyno around 450rwhp with the stage2 kit. that should be around 525hp at thw flywheel. hope my stock clutch will handle it.
-
05-10-2006, 09:34 AM #5
Nice!
Even with a low mileage stock LS1 clutch I wouldn't exspect it to hold up very long with those kind of numbers. I hope I don't unknowingly run up on you expecting an easy kill. Nice ride!!
-
05-10-2006, 09:56 AM #6
- Join Date
- Apr 2006
- Location
- michigan
- Age
- 54
- Posts
- 18
anniversary red- 2003 corvette
Originally Posted by BLACKNIGHT03Z06
i would like to run with a new z06 and see how bad i get beat?
-
05-10-2006, 10:01 AM #7
- Join Date
- Apr 2006
- Location
- michigan
- Age
- 54
- Posts
- 18
anniversary red- 2003 corvette
Originally Posted by BLACKNIGHT03Z06
-
05-10-2006, 10:25 AM #8Originally Posted by 50anv03
-
05-12-2006, 09:07 PM #9
i had the vararam installed couple months ago and the car is showing some differences
for the better
-
05-14-2006, 12:57 PM #10
well most 2002+ Z06's dyno around 350rwhp stock....
with those mods id say 385-400rwhp....
good luck.315rwhp 98 SILVER Z28 (3500lbs)- SOLD
400rwhp 99 HUGGER SS (3375lbs)- SOLD
340rwhp 02 YELLOW Z06 (3040lbs)
-
05-15-2006, 04:35 AM #11
400 after dyno tune is what I'm hoping for. I'll post my numbers in about a month after I return from Brazil. Thanks for all the replies.
-
05-16-2006, 12:19 PM #12
- Join Date
- Apr 2006
- Location
- michigan
- Age
- 54
- Posts
- 18
anniversary red- 2003 corvette
dyno tune is done, i got 426 rwhp. a little less that i was expecting but i will be plenty happy with it. i would have liked to have seen 450 rwhp that was my mark. if i upgrade the stock mass air flow sensor, throttle body ,and bellow can i pick up 20 or so to the rear wheels.
current mods: stage 2 cam & heads, rockers, lifters, pushrods, springs. kooks longtube headers,high flow cats & x pipe. corsa indy mufflers. k&n ram air.
this shit gets expensive.lol
-
08-06-2006, 12:35 PM #13
- Join Date
- May 2006
- Location
- Indiana
- Age
- 43
- Posts
- 51
Silver- 1998 camaro z28
why not just put a 50 shot of nos on it? cost about the same.
-
08-06-2006, 11:14 PM #14
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
2 parts purchased, good deal? Estimated rwhp?
By Aetos in forum External EngineReplies: 27Last Post: 01-19-2009, 05:46 PM -
Engine hp vs rwhp / torque?
By cobrahunter in forum General HelpReplies: 7Last Post: 06-29-2007, 09:51 PM -
Estimated Rwhp???
By chad2000ss in forum Dyno InformationReplies: 0Last Post: 04-02-2006, 09:40 PM -
717 rwhp and 717 ft lb of torque, all at 5200 rpm!
By Exotic Performance Plus in forum Forced InductionReplies: 8Last Post: 03-30-2006, 05:02 AM
Bookmarks