PDA

View Full Version : Engine is HERE!!

Ed Blown Vert
09-16-2005, 11:14 AM
Finally! :woot: :woo:
Ed Blown Vert
09-16-2005, 12:09 PM
Couple more pics
Ed Blown Vert
09-16-2005, 09:14 PM
Since I am waiting here you go.
Ed Blown Vert
09-17-2005, 11:22 AM
Its in ;)
Ed Blown Vert
09-18-2005, 06:03 PM
Torque Arm, AC, power steering, alternater, blower pulley and tensioner is in.
Ed Blown Vert
09-19-2005, 04:48 PM
Few more pics
Ed Blown Vert
09-21-2005, 07:23 PM
Always something. Looks like I can't use my EWP with the SDCE Tensioner. :mad:
Eugenio_SS
09-22-2005, 10:28 AM
doh !
how you gonna fix that problem with the tensioner ?
Ed Blown Vert
09-22-2005, 10:39 AM
I may have to sell the EWP. But someone was able to make it work. So will check it out again.
BIG D's SS
09-22-2005, 12:36 PM
If it ain't one thing it is another. At least it is in and no head bolt problems. Have you talked to Hastings lately?
Ed Blown Vert
09-22-2005, 01:13 PM
Ya, he hasn't done anything with the car. I told him to check on the length of the pushrods.
Eugenio_SS
09-22-2005, 07:28 PM
hope he isn't putting his tools away.
Liquifire
09-24-2005, 12:22 AM
Ya, he hasn't done anything with the car. I told him to check on the length of the pushrods.
so what are the specs on this motor? cam,heads, rotating assembly?
618Hawk
09-25-2005, 12:15 AM
Ed
What are your thoughts on pulling the motor from the top vs the bottom. Looks like it was not to bad. Info please.
Chris
Ed Blown Vert
09-25-2005, 08:28 AM
so what are the specs on this motor? cam,heads, rotating assembly?

Hone block up to .010 with appropriate Torque Plates
Line Hone Main Bores
Set Deck W/ Customer's Pistons
Balance Rotating Assembly
Assemble Engine Short Block
Core Block

Eagle 4340 LS1 4.000 Crankshaft
Callies Compstar 6.125 LS1 Rods W/ ARP 2000 rod bolts
Wiseco Custom Pistons
ARP 234-5608 Main Studs for LS1
Federal Mogul 152M 3/4 Groove Main Bearings for LS1
Clevite CB 663 H Rod Bearings for 2.100 SBC Chamfered Race Bearings
Ed Blown Vert
09-25-2005, 08:30 AM
Ed
What are your thoughts on pulling the motor from the top vs the bottom. Looks like it was not to bad. Info please.
Chris

It wasn't bad at all. I had to pull it almost vertical. I also didn't pull it with the tranny. But my friend Rob did pull it with his M6. My A4 was too long didn't think it would clear.
stevieturbo
09-28-2005, 02:54 PM
Please hurry and get it running so you can tell me how your cam works lol

Lookin good ;-)
Ed Blown Vert
09-28-2005, 03:26 PM
Its Running. ;)

Engine Start (http://www.ls1.com/ed/engine.wmv)
Engine (http://www.ls1.com/ed/engine1.wmv)

Dyno is this Mon.
Natchamp
10-03-2005, 08:09 PM
How much power are you guys getting out of these?

Mark
TimTaylor75
10-05-2005, 12:53 AM
Its Running. ;)

Engine Start
Engine

Dyno is this Mon.

Wow, that sounds incredible. Nice work in a short amount of time.