What series u-joint help

[zmg00camaross]

What series u- joint is stock installing my 9 inch and the builder said it a 1330 so I got a 1330 yoke it's longer than a 1350 so the driveshaft is in the tailshaft properly and length is ok but the u joint cap won't fit right they sit on top of the notch in the yoke where it suppose to be between to hold the caps on hope you understand please help

[zmg00camaross]

Who's weiner do I have to play with to get a responds from around here. PS I will not play with your weiner don't ask.

[Blue_01_Z28]

Who's weiner do I have to play with to get a responds from around here. PS I will not play with your weiner don't ask.

lol sorry man, Well, i don't quite understand so pics would be helpful.

[zmg00camaross]

I can maybe get pic this weekend but what series u- joint is factory 1310 or 1330 or something different. There is notchs so
When the u joint rest in the yoke the caps of the u joint stay in place but my joint hits this notchs so it would be unsafe to drive

[thearborbarber]

The factory uses; Saginaw 44. Also called S44, Saginaw, 3R. It's real close to a 1330 and believe they are interchangeable but you had better take measurements of u-joint first.

[zmg00camaross]

The factory uses; Saginaw 44. Also called S44, Saginaw, 3R. It's real close to a 1330 and believe they are interchangeable but you had better take measurements of u-joint first.

Thanks I am going to measure the u joint and yoke and maybe remove a little material from the yoke to make it fit properly it's a PITA

[thearborbarber]

Napa has conversion u-joint to convert from one to another.

[anniversary30]

I got an alum drive shaft with a 1350 conversion already on it for sale. came off a 6spd 99 ws6 with a moser 9" rearend. 150+ship

[zmg00camaross]

where you at in illinois

[zmg00camaross]

now have a issue with the wheels fitting they are hitting the inner fenders/wheel well both sides i have the zr1 wheels i think the wheels are to wide my 9 inch project has been a nitemare first u -joint wouldnt fit got it to fit today a little grinding and smoothing out fit fine now measured the 10 bolt and measure the houseing and are the same length do not know why it wont fit. starting to go crazy. started to break in the rear with it on jack stands and the rear is kind of howling so i just going fuckin nuts please help anyone

[ls1camino]

now have a issue with the wheels fitting they are hitting the inner fenders/wheel well both sides i have the zr1 wheels i think the wheels are to wide my 9 inch project has been a nitemare first u -joint wouldnt fit got it to fit today a little grinding and smoothing out fit fine now measured the 10 bolt and measure the houseing and are the same length do not know why it wont fit. starting to go crazy. started to break in the rear with it on jack stands and the rear is kind of howling so i just going fuckin nuts please help anyone

Adjustable Panhard Rod.

http://www.ls1.com/forums/showpost.php?p=1880677&postcount=13

[anniversary30]

half hour west of chicago.

[zmg00camaross]

i have a adjustable panhard rod but both wheels are hitting i dont think i can adjust that when both sides are hitting maybe i need more info i have the zr1 wheels and there pretty wide with a 315 tire need help please and thank you

[ls1camino]

i have a adjustable panhard rod but both wheels are hitting i dont think i can adjust that when both sides are hitting maybe i need more info i have the zr1 wheels and there pretty wide with a 315 tire need help please and thank you

Grind the bump stops down till they are even with wheel wells.

[zmg00camaross]

Well I guess I will just remove the bump stops. Just a little cut off wheel and a BFH mite work I didn't. Know I had to remove the bump stops